Laundry Room Plumbing Near Me

Washer hookups and utility sink plumbed in a laundry room

Starting price: Call for pricing

Laundry rooms ask more of plumbing than almost any space in the house: fast fills, full-speed pump-outs, and hot water on demand. Plumbing Pros designs, installs, and repairs laundry plumbing so washers drain cleanly, shutoffs stay easy to reach, and small problems never get the chance to become flooded floors.

What laundry room plumbing covers

Laundry room plumbing is the set of water and drain connections a washing machine needs to run safely. That means hot and cold supply lines with shutoff valves, a standpipe with a trap to carry away discharge, and a vented drain sized for the washer's pump-out rate. It also covers laundry sinks, floor drains, and the hoses that link the machine to the house plumbing. When any of those pieces is missing or undersized, the machine still runs — the room just pays for it.

This work is different from general fixture repair because washers stress plumbing in bursts. A modern machine fills fast and discharges in a violent rush, which is why laundry drains need larger diameters, proper venting, and standpipes set to the manufacturer's height. Plumbing Pros builds every connection around how washers actually behave, not how the house was built decades ago.

What it does not cover: dryer venting and electrical work, gas dryer hookups, and the appliance itself. If the washer's pump, lid switch, or control board is the problem, that is an appliance repair.

When you need it

  • Water on the floor after a drain cycle, or the standpipe overflowing mid-wash
  • A drain that clears slowly, or gurgling sounds from the standpipe
  • Sewer odors around the laundry area, which often mean a dry or missing trap
  • Bulging, rust-stained, or cracked rubber supply hoses
  • Banging pipes when the washer valves snap shut
  • Slow hot water at the washer, or lukewarm fills
  • Stains on the wall or ceiling below the laundry room
  • Planning a new laundry location, remodel, or adding a utility sink

Any one of these is worth a look. Supply hoses fail suddenly and usually when nobody is home, and drain backups have a way of happening during the biggest load of the week.

How the process works

It starts with a conversation about what is happening and which machine you have. Top-load and front-load washers discharge at different rates, and stacking units change how high the standpipe can reasonably reach.

Next comes an on-site inspection. The technician measures standpipe height and diameter, checks the trap and venting, and runs water to test how the drain handles real flow. Supply lines get checked for pressure, hose condition, and whether the shutoffs actually turn.

Then you hear the plan in plain terms: what needs to change, what it will take to do it, and what it affects downstream. Small repairs like hose replacement or a valve swap are often same-visit work. Bigger jobs like rerouting a drain or adding hookups in a new spot are scheduled so the area is ready.

During the work, connections are soldered or crimped, standpipes are set to spec, and valve boxes go in where hands can actually reach them. When everything is connected, the washer runs a full cycle while the technician watches for drips, backups, and hammer noise. The job is done when the laundry behaves the way it should — fills fast, drains clean, and shuts off tight.

What affects the cost

Scope drives cost more than anything. Swapping hoses and a valve is a small job. Moving laundry plumbing across the house or roughing in a brand-new laundry room is a construction project, with framing, code, and permits in the mix.

Access is the next factor. Open stud walls in an unfinished basement make clean, quick runs possible. Finished walls and ceilings mean cutting in, working around obstacles, and patching afterward — all of which adds time.

Materials matter too. A laundry sink and faucet, hammer arrestors, a recessed valve box, and braided stainless supply lines each add to the total. Higher-quality parts outlast cheap ones in a space that shakes every load. Local code requirements, like specific venting or trap arrangements, can change what the job has to include. Timing also plays a role: scheduled installations price differently from urgent repairs.

For an exact number, the honest path is a technician seeing the setup. A few photos of the current hookups and a short description of the problem are usually enough to get a meaningful quote started.

How we serve your area

Plumbing Pros works in all kinds of homes. That includes single-family houses with laundry on the second floor, basement laundry corners in older builds, and condos where shared drains raise the stakes. Rental properties count too, where reliable hookups protect the landlord's investment. The approach stays the same everywhere — measure the machine, size the plumbing to it, and test everything under a full cycle.

Remodeling contractors and home builders bring Plumbing Pros in for laundry rough-ins, because getting standpipe height, drain slope, and venting right before drywall goes up saves everyone trouble later. Homeowners adding a utility sink or moving the washer to a more sensible spot get the same careful layout.

If your laundry room is due for attention, reach out and describe what is going on. One visit is usually all it takes to know exactly what the fix looks like.

Features

  • Washer hookup installation for new machines, replacements, and laundry relocations
  • Standpipe height, diameter, trap, and venting matched to your washer's spec
  • Hot and cold supply lines with reachable quarter-turn shutoff valves
  • Hammer arrestors that absorb the shock of washer valves slamming shut
  • Standpipe and laundry drain clearing when discharge backs up
  • Laundry sink, faucet, and floor drain installation and repair
  • Supply hose replacement with braided stainless steel lines

Benefits

  • Drains sized to keep up with modern high-efficiency machines
  • Fewer leaks thanks to pressure-tested connections and quality hoses
  • Shutoffs you can close in seconds if something starts leaking
  • Quieter cycles with arrestors that calm water hammer
  • Plumbing planned around your exact machine and floor plan
  • Problems caught and fixed before they reach walls and subfloors
  • Work tested under a full wash cycle, not just a quick glance

Frequently asked questions

How much does laundry room plumbing cost?

It depends on the scope. Replacing hoses or a valve is a small job, while roughing in a new laundry room involves framing, code compliance, and permits. Access, materials, and whether the work is scheduled or urgent all move the number. A technician can price it accurately after seeing the setup.

What is a washing machine standpipe, and how tall should it be?

A standpipe is the vertical drain pipe that receives the washer's discharge hose, connected through a trap and vent. Plumbing codes commonly require it to stand between 18 and 42 inches above the trap, and the washer manufacturer may specify a height within that range. Setting it to spec keeps the trap from siphoning dry during pump-out.

Why does my washing machine drain back up or overflow?

The usual causes are a partial lint clog, a drain line sized for an older slower machine, or a venting problem that traps air in the line. Sometimes the standpipe is simply too short, letting the pump push water past the trap. A plumber can find which one it is and correct it.

Should I replace my rubber washer supply hoses?

Yes, especially if they are old, bulging, or rust-stained at the fittings. Rubber hoses weaken with heat and vibration, and burst hoses are one of the most common sources of serious laundry room flooding. Braided stainless steel supply lines resist bursting and last much longer.

Can you add laundry hookups in a garage, basement, or new addition?

Usually yes, as long as hot and cold supply lines, a drain, and proper venting can be run to the spot. The drain needs correct slope and the standpipe needs a trap and vent per local code, and permits may apply. A site visit confirms what the layout allows.

Do you repair laundry sinks and floor drains too?

Yes. Laundry room plumbing covers the whole space: utility sinks, faucets, floor drains, supply lines, and washer hookups. If it carries water in or out of the laundry room, it is part of the job.

Call (877) 401-2673 to get started
Call (877) 401-2673