Shower Repair & Installation Near Me

Starting price: Call for pricing
A dripping showerhead wastes water and wears out the valve behind the wall. Plumbing Pros fixes the plumbing side of showers — valves, cartridges, diverters, supply lines, and drains — and handles full shower installs for remodels and new construction. Valve repairs are usually completed in one visit, and new installs get pressure-tested before the walls close.
What shower repair and installation is
Shower repair fixes the plumbing behind and around your shower — the valve, the cartridge, the diverter, and the drain. The valve mixes hot and cold water, the cartridge or spool steadies temperature, the diverter sends water to the head, and the drain carries it away. Installation is new plumbing for a shower that does not exist yet, or a complete replacement of a worn-out setup, from supply lines to drain.
This service covers the water, not the walls. Tile, grout, glass doors, and stone are finish work for other trades. We set valves at the right depth, run supply lines, and test every joint. The shower is ready for finish with no surprises when the pretty parts go on.
When you need it
Temperature problems, drips, weak flow, and slow drains all point to the plumbing side. Some signs are hard to miss.
- The shower turns scalding or icy when a toilet flushes or the washer fills
- The handle is stiff, spins loosely, or needs jiggling to get water moving
- A steady drip continues minutes after you shut the water off
- The diverter lets half the water run down the tub spout while you shower
- Pressure dropped and a vinegar soak did not bring the head back to life
- The drain gurgles, holds standing water, or gives off a sewer smell
- You are remodeling or building and need plumbing set before tile goes up
How the process works
Start by describing what the shower does and when it started — the valve brand helps if you can see it. The plumber shuts the water off and verifies it is truly off before the trim comes apart.
The valve is identified by its manufacturer pattern, the worn cartridge, spool, or seals come out, and matching replacements go in. Force is never used where a puller belongs, because scored brass means a bigger repair.
With the water back on, the shower is run through full hot, full cold, and the diverter. For new installs, the rough-in happens before the walls close: valve set at the correct depth for the finished wall, lines run, the shower arm backed by solid blocking. Every joint gets pressure-tested and the pan gets flood-tested, so the tile contractor starts with a shower that is proven tight.
What affects the cost
Scope drives the job more than anything. Swapping a single cartridge through the existing trim is a small visit; replacing a valve body behind tile is a different project entirely.
Access matters. An access panel behind the shower wall saves real labor, while a valve buried under finished tile costs more to reach. The brand plays a role too — common cartridges sit on the shelf, while oddball or discontinued valves may need parts ordered in.
Condition counts as well. Corroded supply lines, a tired drain, or a showerhead that needs replacing can fold extra work into the same visit. Remodel timing is the last factor: plumbing done before tile is far simpler than work squeezed in after. Exact pricing depends on your shower, so request a detailed quote when you book.
How we serve your area
Older homes here still run original shower valves, and mineral buildup is their usual downfall. Newer builds tend to have builder-grade fixtures that wear out early. Rentals see heavy turnover, and their shower handles take the punishment.
Plumbing Pros serves all of them — single-family homes, condos, apartments, and the small businesses with employee showers. If your shower drips, scalds, sputters, or drains slowly, tell us what it is doing and we will walk you through the fix and the quote before any work starts.
Features
- Pressure-balancing and thermostatic shower valve repair
- Cartridge, seal, and gasket replacement matched to your valve brand
- Tub-spout and shower-arm diverter repair and replacement
- Showerhead and fixture swaps with proper thread seal and fit
- Complete rough-in plumbing for new shower installations
- Shower drain, strainer, and drain-line repairs
- Pan flood testing and pressure testing before walls close
Benefits
- Steady water temperature with no scalding surprises
- No more drips or running water wasting your utility bill
- Full pressure restored to a weak or sputtering shower
- A quiet diverter that commits fully to the showerhead
- New installs done to plan so finish work fits right
- Problems found before tile goes up, not after
- One plumber for the valve, the drain, and everything between
Frequently asked questions
Why does my shower go cold when someone flushes?
That points to the pressure-balancing spool inside the valve. It is supposed to adjust the hot-cold mix when demand changes elsewhere in the house, but mineral buildup can make it stick. Replacing the cartridge or spool restores steady temperature.
Can a dripping showerhead be fixed without tearing out tile?
In most cases, yes. The cartridge and seals are reachable through the trim plate on the shower wall — no tile comes off. Full valve replacement is the rare job that needs wall access.
How do I know if the problem is the showerhead or the valve?
Soak the showerhead in white vinegar overnight. If flow does not improve, the restriction is deeper — in the valve, the cartridge, or the supply lines — and a plumber should take a look.
What is a shower valve cartridge?
It is the replaceable insert inside the valve body that mixes hot and cold water and sets the flow. Cartridges wear out, get gummed up with mineral scale, or lose their seals, which causes drips, stiff handles, and temperature swings.
Should I repair my old shower valve or replace it?
It depends on three things: whether parts are still made for it, how hard the valve is to reach, and the condition of the body itself. A sound valve with available parts is worth repairing; a corroded body or discontinued line usually means replacement.
How much does shower repair cost?
Scope, access, and parts drive the price. A cartridge swap through the trim plate is the smallest job, while a valve replacement behind tile takes more labor. Request a quote and the plumber will price the job after seeing your setup.
Do you install showers during a bathroom remodel?
Yes — that is the ideal time. The valve goes in at the right depth, the rough-in gets pressure-tested, and the pan gets flood-tested before the tile contractor closes the walls. You get to pick the trim you want once the plumbing is proven.