Whole-House Repiping Near Me

Crew replacing old pipes during a whole-house repiping project

Starting price: Call for pricing

When pinhole leaks, brown water, and fading pressure keep returning, the pipe itself is the problem. Plumbing Pros replaces the whole failing supply system with new copper or PEX, working in stages so your household stays on water. You get an honest assessment first, and a plan that fits your home.

What whole-house repiping is

Whole-house repiping is the complete replacement of a home's hot and cold water supply lines. The new lines run from the point where water enters the house to every fixture. Old pipe — typically galvanized steel, polybutylene, or worn-out copper — is abandoned or removed, and new copper or PEX takes its place. It does not include drain, sewer, or gas lines.

Repiping covers the supply side: the lines that carry water to sinks, showers, toilets, and appliances. Drain and sewer lines are a separate system, and the gas line is untouched. If a section of drain piping is also failing, that gets quoted as its own job — it is never bundled into the repipe silently.

The old pipe usually stays in the walls and is simply disconnected — tearing out every inch of buried pipe would double the mess for no gain. New lines run alongside through open chases, closets, attics, or crawlspaces where they can be routed cleanly. Where a new line must cross a finished wall, a small opening is cut and left documented for patching.

When your home needs it

Repiping is usually the right move when a home's pipes keep failing faster than repairs can keep up. The telltale pattern is repeat leaks in different spots, rust-colored water, and pressure that fades across the house. Homes with galvanized steel or polybutylene pipe — both materials with well-known failure histories — are the usual candidates.

  • Leaks appearing in new spots every few months, not the same fitting twice
  • Brown or reddish water when you first open a tap, especially after the house sat overnight
  • Water pressure fading house-wide, not just at one fixture
  • Visible pipe that is galvanized steel, polybutylene, or thin, green-stained copper
  • A water bill that creeps up with no visible leak — the water may be escaping inside a wall
  • A previous plumber has flagged the pipe material as failing

One bad section can be cut out and replaced. When failures are coming from the material itself — widespread corrosion, brittle polybutylene — each repair fixes a spot while leaving the cause in place. That is the point where patching stops making financial sense.

How the process works

The job starts with a walk-through and a written plan, not a sales pitch. We map every fixture, choose copper or PEX with you, and schedule the work in stages. Old lines are cut over section by section, each new section is pressure-tested before it goes live, and the local inspector signs off on the finished system.

  • Assessment visit: we look at the pipe material, its condition, and how the lines run through your home.
  • A written plan: which material, which route, how many stages, and what the house looks like between stages.
  • Staged installation: new lines go in one section at a time, and each new section is pressure-tested before the old one is disconnected.
  • Pressure test and inspection: the whole system is tested, and permits are closed out with the local inspector.
  • Drywall notes: every wall opening is marked and documented so your patch contractor knows exactly what to close.

Most homes keep running during the job. Water is off only while a section is being swapped, then comes back on before the crew leaves each day. You stay in the house — the work happens around your routine, not the other way around.

What affects the cost

No two repipes price alike because no two houses are alike. The biggest drivers are the size of the home and the number of fixtures. The material you choose matters too, as does access — a crawlspace repipe is a different job than one through a concrete slab. Permits, the condition of existing valves and the water heater connection, and whether walls are drywall or plaster also move the number.

A home visit is the only honest way to price it. We look at the pipe, count the fixtures, check the access points, and put a firm plan in writing. What you will never get is a quote based on square footage alone — it leaves out everything that actually changes the cost.

How we serve your area

Plumbing Pros repipes single-family homes, townhouses, and duplexes — especially older houses where galvanized steel or polybutylene is still in the walls. The assessment is direct: we tell you whether repair, a partial repipe, or a full repipe is the right move, and what each path looks like in your house. Partial repipes are real work, not a dodge — when the failures are confined to the worst runs, renewing just those runs is the sensible middle ground. And when the material itself is done, we say so plainly and lay out the full job.

Features

  • Complete supply-line replacement: every water line in the home, not just the leaking runs
  • Copper or PEX — you pick the material with guidance on the real trade-offs
  • Staged installation with water restored before each evening
  • Dust-controlled cutting and daily cleanup inside your home
  • Permits and inspections handled so the job passes local code
  • New shutoffs, pressure regulator, and supply connections checked as part of the repipe
  • Every wall opening marked and documented for your drywall contractor

Benefits

  • Leaks stop: the failing material behind every patch job is gone
  • Steadier pressure at every faucet, shower, and hose bib
  • Clean, clear water with no rust tint or sediment
  • Quieter lines and fewer surprises behind the walls
  • A supply system that matches the value of the home it serves
  • One project instead of a growing pile of emergency repair bills
  • A strong disclosure point if you ever sell the home

Frequently asked questions

How do I know my house needs repiping instead of another repair?

When leaks keep appearing in new spots and the pipe material is galvanized steel or polybutylene, repairs are treating symptoms. An assessment looks at the material and the pattern of failures, then lays out repair versus partial versus full repipe so you can choose with the facts in front of you.

Copper or PEX — which is better for a repipe?

Both meet code and both serve well; the difference is in how they install. Copper is rigid and familiar, while PEX bends around obstacles with fewer fittings and resists scale buildup. Your water chemistry and the routing of your home decide which makes more sense — we walk through the trade-offs on the visit.

Can we stay in the house while the work is done?

Yes. The job runs in stages and water is off only while a section is being swapped, then comes back on the same day. Most families live around the work without changing their routine.

Will you have to cut lots of holes in my walls?

Openings stay small and are placed where they cause the least damage, usually behind fixtures or in closets. Every cut is documented so your drywall contractor can patch and blend it. The goal is a finished job you cannot see, not a trail of repairs.

What drives the cost of a whole-house repipe?

Home size, fixture count, material choice, access to the lines, permits, and wall material all move the number. Because those vary so much house to house, the real figure comes from a walk-through — never from a guess over the phone.

Do you repipe homes with slab foundations?

Yes. When lines run under a slab, new piping is usually routed overhead through the attic or walls instead of breaking concrete. That keeps the foundation intact and the job far less disruptive.

Call (877) 401-2673 to get started
Call (877) 401-2673